Subject: Re: [suse-axp] Installation on a DPW 500 au with SRM
From: Ruediger Oertel (ro@suse.de)
Date: Thu Jan 20 2000 - 16:15:52 PST
On Thu, 20 Jan 2000, Andreas Vetter wrote:
> Hi!
>
> Is there anybody out there who managed to boot the aboot image from the
> SRM-console?
>
> My problem is that the PCI-IDE controller (with CDROM on it) uses some
> memory that later the QLogic ISP SCSI controller (with harddisk on it)
> wants to use. And then the SCSI controller does not work.
AFAIK, the kernel usually leaves the pci-setup alone when booted from
SRM, so SRM should do the job right. It might be different with a newer
SRM-version, but I wouldn't be sure.
>
>
> Used I/O-ports after booting Suse_6.1_aboot_image from SRM:
> 0060-006f : keyboard
> 0070-007f : timer
> 0170-0177 : ide1
> 02f8-02ff : serial(auto)
> 0376-0376 : ide1
> 03c0-03df : vga+
> 03f0-03f5 : floppy
> 03f7-03f7 : floppy DIR
> 03f8-03ff : serial(auto)
> 90a0-90a7 : ide0
> 90a8-90af : ide1
>
> PCI_IDE: unknown IDE controller on PCI bus 00 device 39, VID=1080, DID=c693
> PCI_IDE: not 100% native mode: will probe irqs later
> ide0: BM-DMA at 0x90a0-0x90a7, BIOS settings: hda:pio, hdb:pio
> ide1: BM-DMA at 0x90a8-0x90af, BIOS settings: hdc:DMA, hdd:pio
> PCI_IDE: unknown IDE controller on PCI bus 00 device 3a, VID=1080, DID=c693
> [...]
> qlogicisp : new isp1020 revision ID (5)
> qlogicisp : i/o region 0x9000-0x90ff already in use
> scsi : 0 hosts.
> scsi : detected total.
> Partition check:
> VFS: Mounted root (ext2 filesystem) readonly.
>
> I only can start the installation from ARCBIOS via the MILO-Miata disk
> then everything works:
> I/O-ports:
> [...]
> 2000-2007 : ide0
> 2008-200f : ide1
> 9000-90fe : qlogicisp
>
>
> PCI_IDE: unknown IDE controller on PCI bus 00 device 39, VID=1080, DID=c693
> PCI_IDE: not 100% native mode: will probe irqs later
> ide0: BM-DMA at 0x2000-0x2007, BIOS settings: hda:DMA, hdb:DMA
> ide1: BM-DMA at 0x2008-0x200f, BIOS settings: hdc:DMA, hdd:DMA
> PCI_IDE: unknown IDE controller on PCI bus 00 device 3a, VID=1080, DID=c693
> PCI_IDE: not 100% native mode: will probe irqs later
> PCI_IDE: port 0x01f0 already claimed by ide0
> PCI_IDE: port 0x0170 already claimed by ide1
> PCI_IDE: neither IDE port enabled (BIOS)
> hdc: TOSHIBA CD-ROM XM-6202B, ATAPI CDROM drive
> ide1 at 0x170-0x177,0x376 on irq 15
> hdc: ATAPI 32X CD-ROM drive, 256kB Cache
> Uniform CDROM driver Revision: 2.55
> [...]
> qlogicisp : new isp1020 revision ID (5)
> scsi0 : QLogic ISP1020 SCSI on PCI bus 01 device 20 irq 27 base 0x9000
> scsi : 1 host.
> Vendor: DEC Model: RZ2CC-KA (C) DEC Rev: 5520
> Type: Direct-Access ANSI SCSI revision: 02
> Detected scsi disk sda at scsi0, channel 0, id 0, lun 0
> scsi : detected 1 SCSI disk total.
> SCSI device sda: hdwr sector= 512 bytes. Sectors= 8380080 [4091 MB] [4.1 GB]
> Partition check:
> sda: sda1 sda2 sda3 sda4 sda7 sda8
> VFS: [...]
>
> Somebody a hint how to boot from SRM? Does Suse 6.3 a better job?
>
> TIA, Andreas.
>
> +-------------------------------------------------------------------------+
> Andreas Vetter
> Universitaet Wuerzburg Telefon: [++49] (931) 888-5723
> Institut fuer Theoretische Physik Telefax: [++49] (931) 888-5141
> Theoretische Physik I
> Am Hubland E-mail: vetter@physik.uni-wuerzburg.de
> D-97074 Wuerzburg
> +-------------------------------------------------------------------------+
>
>
>
>
--
with kind regards (mit freundlichem Grinsen),
Ruediger Oertel (ro@suse.de)
----------------------------------------------------------
does "DONT PANIC" give a hint ?
--
To unsubscribe, e-mail: suse-axp-unsubscribe@suse.com
For additional commands, e-mail: suse-axp-help@suse.com
This archive was generated by hypermail 2a22 : Tue Feb 01 2000 - 05:33:35 PST